Prototyping

Vacuum Casting (Urethane Casting): From SLA Master Pattern to Low-Volume Parts

Does your housing batch justify the cost of an injection mold? Vacuum casting, also called urethane casting, offers low tooling cost for low-quantity production, according to Design for Manufacturability Handbook. Will the cast resin meet your material requirements? Its name alone doesn't establish equivalence to your intended injection-molded grade.

This article explains the master-pattern-to-silicone-mold workflow, compares tooling economics and mold life, and helps you weigh casting against SLA printing and CNC machining. For a project review, include your drawing, target quantity and material requirements in your quote request.

What Is Vacuum Casting (Urethane Casting)?

Vacuum casting produces plastic parts using a master pattern and a silicone mold. In urethane casting, polyurethane or another two-part resin fills that mold, according to Machining and Metalworking Handbook. The mold uses room-temperature vulcanizing (RTV) silicone, which cures at room temperature.

Search results for "vacuum casting" also cover metal casting. This article addresses plastic-part casting only.

Degassing removes trapped gas at two points. Before the mold is poured, Machining and Metalworking Handbook specifies mixing and degassing the silicone according to its manufacturer's recommendations. The resin needs separate attention. According to NASA-TM-X-59180, mixing two-part castable polyurethane traps air, while moisture can cause carbon dioxide to form. The report identifies vacuum degassing as necessary to remove those gases.

How Does Vacuum Casting Work, Step by Step?

Silicone-mold urethane casting follows five steps from master preparation to part removal, according to Machining and Metalworking Handbook. Dimensional control starts with the pattern's shrinkage allowance and continues through mold clamping.

  1. Prepare the master with a resin shrinkage allowance. The pattern dimensions must account for the casting resin's shrinkage, according to Machining and Metalworking Handbook. Your drawing's nominal dimensions aren't automatically the correct master dimensions.

  2. Define the parting line and runners. The parting line determines where the mold separates; runners provide channels for casting material. A Guide to Additive Manufacturing places this preparation before silicone mold construction. Flexible silicone can accommodate small to moderate undercuts, according to Machining and Metalworking Handbook.

  3. Make and degas the silicone mold. Mix and degas the silicone per its manufacturer's instructions before pouring it around the pattern. Machining and Metalworking Handbook describes a two-piece method with about 24 hours of curing for each half. That is mold preparation time.

  4. Remove the master and cut pouring and vent openings. Once the silicone cures, separate the mold and remove the pattern. Machining and Metalworking Handbook places the pouring opening at the part's highest point and vents wherever air could become trapped.

  5. Cast the resin, let it harden and remove the part. Apply a release agent matched to the urethane, clamp the mold, then mix and slowly pour the resin. Excessive clamping can distort the compressible rubber cavity, according to Machining and Metalworking Handbook. The same source gives a formulation-dependent hardening time of 1–15 minutes before part removal. This isn't a project lead time.

Casting adds mold preparation and resin hardening after the master is ready. Our standard SLA printing lead time is 1–4 working days, excluding shipping. That figure covers printing, not the complete casting workflow, so the master's preparation belongs in your schedule alongside the choice of printing process.

Why Is SLA Used for the Master Pattern?

Our in-house SLA process produces detailed master patterns with an as-printed surface roughness of Ra 0.8–1.6 μm. SLA means stereolithography, a resin 3D printing process. Its minimum feature size is 0.3 mm, giving you a specific detail limit to discuss during review.

SLA is one route to the master. Machining and Metalworking Handbook permits patterns made by any rapid-prototyping process. Our surface and feature specifications describe the printed master, not the accuracy or finish of the cast part.

The master must also include the resin's shrinkage allowance, according to Machining and Metalworking Handbook. A smooth master alone doesn't establish whether a cast housing meets your drawing. Your intended use should guide which dimensions and appearance requirements you specify for review.

What Is Vacuum Casting Used For?

We use in-house urethane casting for housings and covers in low-volume production, design validation and product development. Design for Manufacturability Handbook identifies low tooling cost as a reason to consider casting for prototypes and low-quantity production.

Three applications shape what you should send with your drawing:

  • Design validation: identify the dimensions and design features you want to assess.
  • Product development: state what the part needs to demonstrate.
  • Low-volume housings or covers: Design for Manufacturability Handbook notes that casting combines low tooling cost with higher labor content.

The application establishes what you need the part to do. Material selection then needs to address those requirements.

Which Materials Can You Vacuum Cast?

Silicone molds can receive polyurethane, ABS or polyamide materials, according to A Guide to Additive Manufacturing. Which formulation meets your housing's requirements? A material name alone doesn't establish a match to your intended injection-molded grade.

Published handbooks list castable materials; our own vacuum-casting options are listed separately.

Source Materials Listed What the Evidence Establishes
A Guide to Additive Manufacturing ABS, polyurethanes and polyamides These materials can be cast into silicone molds.
Design for Manufacturability Handbook Urethane, polyester, epoxy, acrylic and nylon These materials can be cast; urethane offers different flexibilities, with or without foaming.
Our in-house vacuum casting ABS, PP, PC, PA and PMMA Our listed vacuum-casting options; exact formulations and property matches need project review.

Urethane flexibility varies by formulation, according to Design for Manufacturability Handbook. Specify the behavior your component needs rather than relying on a material label. For a housing intended for later injection molding, the proposed casting formulation needs review against your production grade.

Appearance also involves formulation. Machining and Metalworking Handbook describes urethane with dyes or fillers, associating chopped glass fiber with increased strength and metal powders with a metallic appearance. Those are formulation-specific effects.

Can Parts Be Color Matched to Pantone or RAL?

Yes, our in-house painting service offers Pantone or RAL color matching. Color matching adds 2–3 days, and spray coating in primer, matte or gloss adds 1–2 days.

Finish Option Available Specification Additional Time
Color matching Pantone or RAL code 2–3 days
Spray coating Primer, matte or gloss 1–2 days

Include the color code and required finish in your quote request. These finishing allowances don't establish a combined project schedule, and paint adhesion to your specific cast urethane needs separate review.

What Are the Key Differences Between Urethane Casting and Injection Molding?

Silicone-mold urethane casting has low tooling cost for low-quantity production, according to Design for Manufacturability Handbook. Injection molds need enough production quantity to amortize their cost, according to the same handbook. Your production run must carry that investment.

The comparison below separates tooling economics, material evidence and preparation time.

Decision Factor Silicone-Mold Urethane Casting Injection Molding
Tooling investment Low tooling cost supports prototype and low-quantity production. Mold cost must be amortized over a large enough quantity.
Production-run economics Higher labor content is acceptable for prototype and low-quantity work. Tooling investment must be spread across the production run.
Material evidence Polyurethane or other two-part resins are cast into silicone molds. The supplied evidence establishes no direct property equivalence to your intended molded grade.
Tooling preparation A Guide to Additive Manufacturing describes making a silicone mold within one day. The evidence supplies no current injection-tooling lead time.

For a concrete example, Design for Manufacturability Handbook describes a cast-urethane fixture block made in a silicone mold. The quantity was too low to spread the injection-mold investment across the run. That example supports comparing tooling investment against your quantity, rather than applying a universal break-even cutoff.

Preparation times carry their own conditions. Machining and Metalworking Handbook describes approximately 24 hours of curing for each half of a two-piece silicone mold. That differs from the one-day mold-making description in A Guide to Additive Manufacturing. Neither establishes a delivery date for finished parts.

How Many Parts Can One Silicone Mold Make?

A typical RTV silicone mold makes approximately 30–50 castings, depending on resin, geometry and additives, according to Machining and Metalworking Handbook.

Published mold-life estimates differ in scope and conditions. Each figure below belongs to its source; none establishes mold life for your part.

Source Reported Mold Life Conditions
Machining and Metalworking Handbook Approximately 30–50 castings Typical RTV silicone mold; depends on resin, part geometry and fillers or additives.
Design for Manufacturability Handbook 100–250 shots Most silicone molds; depends on material and part complexity.
A Guide to Additive Manufacturing 10–100 shots Short-run soft tools, including silicone molds; wear or damage limits use.

A shot means one casting cycle. Keep these estimates separate rather than combining them into one planning range.

Sticking provides a concrete stopping condition. Machining and Metalworking Handbook describes repeating casting until polyurethane begins sticking despite the release agent. For complex molds, A Guide to Additive Manufacturing describes replacing thin silicone sections with metal or polymer inserts to extend durability.

For your cost comparison, the useful question is how many molds your geometry, resin and target quantity may require.

Is Vacuum Casting Expensive?

Silicone-mold casting offers low tooling cost but higher labor content, according to Design for Manufacturability Handbook. That combination makes casting practical for prototypes and low-quantity production. Tooling investment must be spread across the production run, according to the same handbook. A smaller run leaves fewer parts to carry that investment.

The trade-off has two sides:

  • Silicone-mold casting: low tooling cost supports low-quantity work despite higher labor content.
  • Injection molding: mold cost needs enough quantity to amortize.

Design for Manufacturability Handbook describes a cast-urethane fixture block whose quantity couldn't justify injection tooling. That example supports reviewing your drawing and quantity, rather than choosing a process from a universal economic cutoff.

When Should You Choose 3D Printing, Vacuum Casting or CNC Machining?

Choose SLA for appearance prototypes, vacuum casting for low-volume housings and covers, or CNC machining when our standard ±0.05 mm tolerance suits your drawing. Does your part need appearance review, or a low-volume production run with molded-like parts?

Process Supported Applications Dimensional Information Timing Evidence
SLA 3D printing Appearance prototypes, clear parts and consumer electronics housings. Standard tolerance ±0.2 mm for parts under 25 mm. Standard lead time 1–4 working days, excluding shipping.
Vacuum casting Low-volume housings and covers, design validation, product development. Cast-part dimensions need project review; the master's tolerance doesn't set the casting's tolerance. Master preparation precedes mold construction.
CNC machining Custom components for prototyping and low-volume production. Standard tolerance ±0.05 mm, subject to part review. Standard lead time 10–15 days, excluding shipping.

For prototyping, SLA addresses the appearance and clear-part applications listed above. Casting adds a master and silicone mold before resin casting begins. Those stages need separate scheduling; the SLA lead time alone can't establish when cast parts will be ready.

For low-volume production, our casting applications include housings and covers. If your plastic component has dimensional callouts that favor CNC machining, compare those callouts with our machining specifications during review. Submit the drawing, intended use and target quantity together so we can review the process against your requirements.

How Do We Run a Vacuum Casting Project?

We run vacuum casting projects with in-house SLA, casting and painting, starting with a free DFM printability check. DFM means design for manufacturability. We accept STL, STEP, 3MF and OBJ files, with a printability-check response within 24 hours. That response is separate from quotation turnaround and production lead time.

We produce the SLA master in-house, then make the silicone mold and cast the parts. Your drawing should identify critical dimensions for review, and the master needs a resin shrinkage allowance, according to Machining and Metalworking Handbook. For painting, we offer Pantone or RAL matching, plus primer, matte and gloss finishes.

Our quality system is certified to ISO 9001. Final inspection includes CMM measurement of critical dimensions, and the inspection report ships with the parts. Dimensional inspection and first article inspection reports are available, along with material certificates. Include the intended use, dimensional callouts and required finish alongside your target quantity.

Send your CAD file and target quantity for a vacuum casting quote

Frequently Asked Questions

What is a vacuum casting?

Vacuum casting here refers to plastic-part production using a master pattern and a silicone mold. For urethane casting, polyurethane or another two-part resin fills the mold, according to *Machining and Metalworking Handbook*. The same handbook specifies degassing the silicone before pouring it around the master. The RTV silicone cures at room temperature.

What is vacuum casting used for?

We use vacuum casting for custom housings and covers, low-volume production, design validation and product development. Silicone-mold casting also supports prototypes and low-quantity production through low tooling cost, according to *Design for Manufacturability Handbook*. Your intended use should guide the material and dimensional requirements you submit for review.

Is vacuum casting expensive?

Vacuum casting has low tooling cost but higher labor content, according to *Design for Manufacturability Handbook*. That trade-off supports prototype and low-quantity production. Injection molds need enough quantity to amortize their cost, according to the same handbook. Your drawing and target quantity provide the basis for comparing those production routes.

What are the key differences between urethane casting and injection molding?

Urethane casting uses silicone molds and offers low tooling cost for low-quantity production, according to *Design for Manufacturability Handbook*. Injection molds need enough production quantity to amortize their cost, according to the same handbook. Tooling investment must be spread across the production run.

What is urethane casting?

Urethane casting makes plastic parts by casting polyurethane resin into a silicone mold formed around a master pattern, according to *Machining and Metalworking Handbook*. Urethane formulations offer different flexibilities, according to *Design for Manufacturability Handbook*. The pattern must account for resin shrinkage, according to *Machining and Metalworking Handbook*.